Phase-5 Polish Does it all. Restores and Revives Finishes,  Removes swirls, scratches, oxidation and paint defects leaving the finish smooth clean and brilliantly glossy. For all painted surfaces especially fiberglass, and Gel Coats making it ideal for boats and RV’s. Speeds up paint restoration with minimal dusting. Phase-5 is an aggressive polish that begins working like a virtual compound cutting fast and accurately capable of removing moderate to heavy surface imperfections. As buffing continues its unique abrasive system breaks down into finer and finer tiny particles that eventually become super fine polish.  This metamorphosis enables the professional user to compound, polish and protect in one easy step. For superior results buffer speed should be between 1800 and 2200 RPM.

Phase-5 Polish eliminates the need for 3 compounds and a polish that 4 products in all. Phase-5 Polish leaves very little haze, if any at all.  

Clients And Professionals Share Some Experiences



" Detailing Boats in the Marina has been our business for 20+ yrs. Here is California, the sun really takes its toll on us and the yachts. Having a professional line of Products to use can make or break a business.    Chemical Guys Phase % polish and the Jetseal Sealant are " MUST HAVE" products for any marine detailer. Great products and great support...Thanks Guys"

-Pride & Shine Yacht Detailing, Marina CA.

" Our 2005 Prowler 39.5 foot RV was looking a little under the weather.  Phase-5 restored it to better conditions then the day we picked it up. Thank You so much for your great product"

-Dennis & Martha Higgents Zolfo Springs, Florida

" My brand new Forest River Wildwood 34.5 ft.  Trailer sat in the sun under some trees for 7 months, it looked 70 yrs old, like me.  Saturday some boys helped me polish it up with your Phase Products and then we waxed it up with the Mseal. I can safely say it looks better then anything on the road"

- Don Harley Judsonia, Arkansas

If your looking for the Phase-5 in 1 gallon size click here or picture.

Application by Hand:

1. Mist desired pad to be used with Chemical Guys POLISHING PAD CONDITIONER to moisten the foam and reduce friction. Apply a nickel size amount of Phase-5 Polish to the applicator.
2. Work polish in a back and forth, work in 2 x 2 sq. foot sections until the entire surface is done.

Note: General Hand application of Phase-5 Polish by hand will remove light oxidation and minor imperfections while enhancing gloss.  Doing the work by hand will not deliver the same superior results achievable with a PC or Rotary. For paint correction, it is always recommended to use a polisher.

Application by Machine:

1. Mist desired pad to be used with Chemical Guys POLISHING PAD CONDITIONER to moisten the foam and reduce friction. Apply a nickel size amount of Phase-5 Polish to the applicator.
2. Always make sure the surface to be compounded is clean and dry.
3. If surface is freshly or recently painted , always allow time to properly cure.
4. It is always recommended to apply Polish out of direct sunlight.
5. Though product will work great even in the sun, maximum work time is achieved out of direct sunlight.
6. For light jobs us MPT YELLOW PAD.
7. For Large Boats and RV’s or larger more oxidized surfaces use a wool or foam polishing pad, like Chemical Guys MPT YELLOW PAD.
8. Apply a 4-6 inch line of Polish to the surface.
9. With the polisher turned off, spread the polish over about a 2 x 2 sq. ft. area.
10. Polish at 1200-1800 RPM  on rotary polisher or 5000-6000 OPM for Dual-Action Polisher.
11. Work area slowly across and then up and down the area.
12. Always double check your work after several passes assure proper results.
13. Wipe surface area with a lightly damp microfiber towel.
14. If necessary, follow with FP-Final Polish or Pro-Polish to enhance or restore maximum gloss and shine.
15. Always apply a wax or sealant after compounding or polishing.
16. CG recommend JetSEAL for maximum protection, durability and wet mirror shine.